HomeMy Public PortalAboutLovell Av_1101ELEVATION CERTIFICATE
FEDERAL EMERGENCY MANAGEMENT AGENCY
NATIONAL FLOOD INSURANCE PROGRAM
ATTENTION: Use of this certificate does not provide a waiver of the flood insurance purchase requirement. This form is used only to
provide elevation information necessary to ensure compliance with applicable community floodplain management ordinances, to
determine the proper insurance premium rate, and /or to support a request for a Letter of Map Amendment or Revision (LOMA or LOMR).
Instructions for completing this form can be found on the following pages.
O.M.B. NO. 3067 -0077
Expires May 31, 1996
SECTION A PROPERTY INFORMATION
FOR INSURANCE COMPANY USE
BUIL
ING OWNER'S NAME
POLICY NUMBER
STREET ADDRESS (Including Apt., Unit, Suite and/ r`BIIdg. Number) OR P.O. ROUTE AND BOX NUMBER
I 1 �V
COMPANY NAIC NUMBER
OTH R DESCRIPTION L t and Bloc Numbers, etc.)
Z-- WA�p
67_
CODE
L�J
SECTION B FLOOD INSURANCE RATE MAP (FIRM) INFORMATION
CITY
Provide the following from the proper FIRM (See Instructions):
1. COMMUNITY NUMBER
\ Z; b A-
2. PANEL NUMBER
2
3. SUFFIX
G
4. DATE OF FIRM INDEX
(0 Ai // (3,
5. FIRM ZONE
A 8
6. BASE FLOOD ELEVATION
(in AO Zones, use depth)
I Z
7. Indicate the elevation datum system used on the FIRM for Base Flood Elevations (BFE): 1_7 NGVD '29 Li Other (describe on back)
8. For Zones A or V, where no BFE is provided on the FIRM, and the community has established a BFE for this building site, indicate
the community's BFE: I ! ! feet NGVD (or other FIRM datum —see Section B, Item 7).
SECTION C BUILDING ELEVATION INFORMATION
1. Using the Elevation Certificate Instructions, indica e t e diagram number from the diagrams found on Pages 5 and 6 that best
describes the subject building's reference level
2(a). FIRM Zones Al -A30, AE, AH, and A (with BFE). The top of the reference level floor from the selected diagram is at an elevation
of I 1 ( 16.1feet NGVD (or other FIRM datum —see Section B, Item 7).
(b). FIRM Zones V1 -V30, VE, and V (with BFE). The bottom of the lowest horizontal structural member of the reference level from
the selected diagram, is at an elevation of I 1 I Li feet NGVD (or other FIRM datum —see Section B. Item 7).
(c). FIRM Zone A (without BFE). The floor used as the reference level from the selected diagram is 1 L feet above or
below Li (check one) the highest grade adjacent to the building.
(d). FIRM Zone AO. The floor used as the reference level from the selected diagram is I ! II feet above or below L.J (check
one) the highest grade adjacent to the building. If no flood depth number is available, is the building's lowest floor (reference
level) elevated in accordance with the community's floodplain management ordinance? Ell Yes Z No i7, Unknown
3. Indicate the elevation datum system used in determining the above reference level elevations: ❑ NGVD '29 IL11 Other (describe
under Comments on Page 2). (NOTE: If the elevation datum used in measuring the elevations is different than that used on
the FIRM [see Section 8, Item 7], then convert the elevations to the datum system used on the FIRM and show the conversion
equation under Comments on Page 2.)
4. Elevation reference mark used appears on FIRM: 1 Yes No (See Instructions on Page 4)
5. The reference level elevation is based on: _yctual construction construction drawings
(NOTE: Use of construction drawings is only valid if the building does not yet have the reference level floor in place, in which
case this certificate will only be valid for the building during the course of construction. A post- construction Elevation Certificate
will be required once construction is complete.)
6. The elevation of the lowest grade immediately adjacent to the building is: ! l' i3.feet NGVD (or other FIRM datum -see
Section B, Item 7).
SECTION D COMMUNITY INFORMATION
1. If the community official responsible for verifying building elevations specifies that the reference level indicated in Section C, Item 1
is not the "lowest floor" as defined in the community's floodplain management ordinance, the elevation of the building's "lowest
floor" as defined by the ordinance is: I 1 1 1 IL feet NGVD (or other FIRM datum —see Section B, Item 7).
2. Date of the start of construction or substantial improvement
FEMA Form 81 -31, MAY 93
REPLACES ALL PREVIOUS EDITIONS SEE REVERSE SIDE FOR CON11NUAT1ON
SECTION E CERTIFICATION
This certification is to be signed by a land surveyor, engineer, or architect who is authorized by state or local law to certify elevation
information when the elevation information for Zones A1—A30, AE, AH, A (with BFE),V1— V30,VE, and V (with BFE) is required.
Community officials who are authorized by local law or ordinance to provide floodplain management information, may also sign the
certification. In the case of Zones AO and A (without a FEMA or community issued BFE), a building official, a property owner, or an
owner's representative may also sign the certification.
Reference level diagrams 6, 7 and 8 - Distinguishing Features —If the certifier is unable to certify to breakaway /non- breakaway wall,
enclosure size, location of servicing equipment, area use, wall openings, or unfinished area Feature(s), then list the Feature(s) not
included in the certification under Comments below. The diagram number, Section C, Item 1, must still be entered.
1 certify that the information in Sections 13 and C on this certificate represents my best efforts to interpret the data available.
I understand that any false statement may be punishable by fine or imprisonment under 18 U.S. Code, Section 1001.
CERT IER • A E
TITLE
A ►DRESS
SIGNATU
Copie
LICENSE NUMBER (or Affix Seal
COMPANY NAME
4-1
CITY
744-
(4 L
PHONE 3 z
this Certificate for: 1) community official, 2) insurance agent/company, and 3) building owner.
OMMENTS-
ON
SLAB
A
ZONES
V
ZONES
BASE
FLOOD
ELEVATION
REFERENCE
LEVEL
ADJACENT
GRADE
WITH
BASEMENT
A
ZONES
BASE
FLOOD
ELEVATION
ADJACENT
GRADE
REFERENCE
LEVEL
ON PILES,
PIERS, OR COLUMNS
A V
ZONES ZONES
REFERENCE
LEVEL
BASE
FLOOD
ELEVATION
ADJACENT
The diagrams above illustrate the points at which the elevations should be measured in A Zones and V Zones.
Elevations for all A Zones should be measured at the top of the reference level floor.
Elevations for all V Zones should be measured at the bottom of the lowest horizontal structural member.
Page 2